|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Site Navigation Asahi Solder DTI Hand Tools Elcontrol Electrolube Formit Hakko Kinsten Light Emitting Diodes MeanWell SMPS Module Motech Test Multicore Quick-Mark Rota-Spray Very Useful Things Clearance
|
Electrolube
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| FRE - Freezer | ||||||||||||||||
 Electrolube Freezer is a powerful non-corrosive refrigerant for use as a rapid and safe method of cooling small components, particularly in electrical and electronic equipment, and to detect faulty soldered joints and overheating components.For use on non-static sensitive electrical and electronic circuitry for detection of faulty joints and overheating components, for the testing of thermostats and other thermosensitive components, repairing thermometer threads and small mechanical shrink fittings and for plumbing applications. Download Technical Data Sheet |
||||||||||||||||
|
||||||||||||||||
| MCF - Minimal Charging Freezer | ||||||||||||||||
 Electrolube Minimal Charging Freezer is a powerful non-corrosive refrigerant for use as a rapid and safe method of cooling small components, particularly in electrical and electronic equipment.MCF is particularly suitable for testing static sensitive devices as it has been specially formulated to induce the absolute minimum charge in components being tested. MCF does not exhibit the “wetness” normally associated with “anti-static” freezer products, therefore it is possible utilise the speed of dissipation of frost as a test method. Download Technical Data Sheet |
||||||||||||||||
|
||||||||||||||||
| LRM - Label Remover | ||||||||||||||||
 Label Remover has been specially formulated for the quick and efficient removal of paper based pressure sensitive adhesive labels.Spray or wipe on, leave in contact for 5 minutes and then peel off label. Wipe suface clean. Allows label to be simply peeled off without leaving adhesive residue or scratching surface. Harmless to most plastics, rubbers, elastomers, and surface coatings when used as directed. Download Technical Data Sheet |
||||||||||||||||
|
||||||||||||||||
| SCP - Silver Conductive Paint | ||||||||||||||||
 Silver Conductive Paint, SCP, provides a thin, smooth, adherent, flexible film of high electrical conductivity on a wide range of substrates, including plastics, paper, wood, textiles, glass, ceramics and metals. It can be applied by brushing, spraying, dipping, or a pencil and will dry at room temperature.Used for PCB design and repair, repairing heated rear window-screens, mark sensing e.g. on recording tapes, screening plastic housings against high frequency fields, earthing strips, leading off primary electrons in scanning microscopy, connections to non-solderable surfaces, electroplating pre-coats, contact surfaces, potentiometer tracks, etc. Download Technical Data Sheet |
||||||||||||||||
|
||||||||||||||||
| SMFL - Surface Mount Rework Flux | ||||||||||||||||
 Electrolube Surface Mount Rework Flux is a quick drying, mildly activated (RMA type) no-clean flux in aerosol form for use when removing and replacing surface mount components. The aerosol is fitted with a wide angle actuator to give a protective film and an extension tube actuator for pinpoint application. Particularly recommended for precision products e.g. telecommunications or professional computers where a high degree of reliability is required.SMFL can also be used as an anti-tarnish, protective film on bare copper or tinned tracks providing excellent solderability for up to six months. Download Technical Data Sheet |
||||||||||||||||
|
||||||||||||||||
| EPE - Permaguard Dewatering Spray | ||||||||||||||||
 Permagard 40 is a multi-purpose maintenance fluid which will de-water, penetrate, lubricate and protect from rust and corrosion.It displaces water, moisture and damp from all surfaces because of its acute angle of contact against the relatively high angle presented by water, its very low surface tension and high capillary action drives water away from the surfaces and fills the pores as the water disperses. Download Technical Data Sheet |
||||||||||||||||
|
||||||||||||||||
| AGC / ASP Antiseize | ||||||||||||||||
 AGC Copper Anti-Seize Fluid is a long lasting and effective material for the protection of metals exposed to aggressive environments. For use on threaded metal components, it allows them to be easily loosened even after exposure to high temperatures or corrosive chemical atmospheres. The high copper content ensures good lubrication.Download AGC Technical Data Sheet An alternative product is Electrolube ASP high temperature anti-seize paste recommended for all jobs where speed of assembly and dismantling is essential including soldering iron tips. Download ASP Technical Data Sheet |
||||||||||||||||
|
Prices do not include GST. 10% GST applies to goods delivered in Australia.
Australian GST is not paid on shipments despatched to an international destination.
Prices are in Australian Dollars and subject to change without notice.
Sales are subject to Computronics General Terms and Conditions of Sale
E.& O.E.
Due to continuing product improvement efforts, specifications and appearance are subject to change without notice.
All mains powered equipment supplied by Computronics operates from 240Vac, 50Hz supply unless otherwise specified.
To place an order, select the order quantity and click the ADD button.
Add items from other pages - if required.
When all items have been added, click a View Cart link to edit your order
and continue to the secure order page.
If ADD buttons are not visible, then Java might not be installed or enabled.
Java can be downloaded from the GET JAVA site.
Java and SSL must be enabled for the shopping cart to operate.